48V 100Ah V2 Elite Series – Heated & Bluetooth & Victron Comms LiFePO4 Batttery
$1,999.00
-
Description
- LiFePO4 Chemistry
- Group 8D Size (20.9″ x 8.7″ x 12.1″) L x W x H
- 100Ah Capacity
- 150A Max Continuous Discharge (300A 30s Discharge)
- 150A Max Continuous Charge (300A 10s Charge)
- IP67 Rated, Dust and WATERPROOF
- HEATED – Internal heating for below 0C charging
- BLUETOOTH – iOS and Android Apps
- CANBUS Communication allows BMS to communicate directly with Victron OS
- Mountable ON/OFF Switch
- Mountable Battery gauge
- Built-in Smart Battery Management System (BMS)
- Internal fuse with current and temperature protections
- Over charge and over discharge protection
- Over current and short circuit protection
- High & low temperature disconnects
- 3500+ Cycle life & Maintenance-free
- 11 Year Manufacturer Warranty
ConfigurationCell Configuration: 16S1PChemistry: LiFePO4CurrentAh Capacity: 100AhMax Continuous Discharge Amps: 150AMax Charge Current Amps: 150AMax Discharge Peak Current Amps: 300A @ 30secSeries | Parallel: Max (16) in Parallel, Plug & PlayVoltage: 51.2VMax Charge Voltage: 58.4VOperating Voltage Range: 48.0V – 58.4VTemperatureCharge Temp Range: -30°C (-22°F) / 55°C (131°F) (with heating)Discharge Temp Range: -20°C (-4°F) / 55°C (131°F)Storage Temp: -20°C (-4°F) / 45°C (113°F)Weight: 97lbsDimensionsLength: 20.75 (inches)Width: 8.5 (inches)Height: 12 (inches)Recommended Charging SettingsBatteries employed in non-Victron systems should utilize the following settings:
-
- Absorption voltage of 56.8V with an absorption time of a minimum of 15 minutes per battery.
- Float voltage of 54.0V
- Equalization off
- No temperature compensation
- To use the V2 Elite with Victron systems. Set up the battery comm harness and gauge as follows:
- Plug with waterproof bung plugged into master blue port.
- RJ45 cable out of master black port and into slave1 blue port.
- RJ45 cable out of slave1 black port and into slave blue port and so on to daisy chain up to 16 batteries in parallel.
- Set dips as per manual.
- Plug in grey RJ45 plug into the Cerbo or Ekrano GX BMS CAN port or if you have the new Cerbo Mk2 plug grey plug inot VE-CAN1 or VE-CAN 2 and change the VE can port speed to 500 KBPS LV.
- To confirm proper reporting, go to the GX/touch screen and confirm the Epoch battery shows up on the device list. Click on the battery line, go to Details. Check to see the number of modules online is equal to the number of batteries installed. Check that the number of AH is equal to the number of AH installed.
- In the GX device/touch screen turn on DVCC, set controlling BMS to Epoch, set battery monitor to Epoch.
- The system should say External Control on the GX touch screen Inverter tile when charging (but not while inverting). The system will automatically cycle to 56.8V with an absorption time of a minimum of roughly 15 minutes per battery followed by 54.0V float voltage.
- It is recommended to manually program the Multiplus, Quattro and all other charge source to these same parameters in case of CAN communication loss.
Over time there will be additional refinements and improvements as needed.
-
Reviews (0)
Shipping and Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Reviews
There are no reviews yet.